FTBR LOGO

SN-95 13" Front Rotor Set

FT 8000 and FT 8000 HD

Full Tilt Boogie Racing now offers a two piece 13" front Cobra rotor set.
These rotors are a direct replacement for all Cobras, Mach 1's and Bullitts from 1994 through 2004 using the
OEM PBR calipers or the Y2KR Brembo four piston calipers.
Because Mustangs are heavy, particularly on the front end, these would be a great addition
to anyone looking to reduce weight.
With rotors being unsprung, rotating mass, this weight reduction comes as a huge bonus.
Two versions of these rotors are available.
A lightweight version (FT 8000) for street and strip use and a heavy duty version (FT 8000 HD) for road racing.
Both versions of these rotors utilize the same hardcoated aluminum hat and attaching hardware.
The only difference in the two versions is the rotor casting that is used to make the finished product.
All rotors are directional vaned for high performance cooling,
stress relieved, slotted and clear zinc plated.


FT 8000 Front Rotor Set - Street/Strip

BREMBO 1 PIECE ROTOR 19.1 LBS  EACH FTBR FT 8000....14.7 LBS EACH FTBR LIGHTWEIGHT ROTOR SET... FT 8000
Brembo one piece rotor weighs
in at a HEFTY 19.1 LBS!
Full Tilt Boogie Racing's lightweight rotor
for street/drag strip use
weigh in at 14.7 lbs.
Lightweight rotor pair.
FT 8000
This equates to a weight savings of 4.4 lbs each for a
total savings of 8.8 lbs.

The air gap on this rotor is .620" and the rotor face thickness of .250" each.
The aluminum hats are hardcoated for aesthetics and also to prevent oxidation.
The rotor rings are clear zinc plated to help resist corrosion.

This front rotor set is recommended only for STREET/STRIP duty.
Go Back To The Previous Page

FT 8000 HD Front Rotor Set - Heavy Duty/Road Race

BREMBO 1 PIECE ROTOR 19.1 LBS  EACH FTBR FT 8000 HD....16.1 LBS EACH FTBRHEAVY DUTY ROTOR SET... FT 8000 HD
Brembo one piece rotor weighs
in at a HEFTY 19.1 LBS!
Full Tilt Boogie Racing's heavy duty rotor for
road race use weigh in at 16.18 lbs.
Heavy duty rotor pair.
FT 8000 HD
This equates to a weight savings of 2.92 lbs each for a total savings of 5.84 lbs.

The air gap on this rotor is .520" and the rotor face thickness of .295" each,
same as the one piece Brembo.
The aluminum hats are hardcoated for aesthetics and also to prevent oxidation.
The rotor rings are clear zinc plated to help resist corrosion.

This front rotor set is recommended for ROAD RACE duty.
WARRANTY AND DISCLAIMER
WARRANTY AND DISCLAIMER: FULL TILT BOOGIE RACING, INC., A WISCONSIN CORPORATION (“SELLER”), HEREBY WARRANTS THAT THE ENCLOSED AUTOMOTIVE COMPONENTS ARE FREE FROM DEFECTS IN WORKMANSHIP AT THE TIME OF SHIPMENT, BUT DISCLAIMS AND EXCLUDES ANY AND ALL OTHER EXPRESSED OR IMPLIED WARRANTIES REGARDING THE ENCLOSED AUTOMOTIVE COMPONENTS. PURSUANT TO THE UNIFORM COMMERCIAL CODE, ARTICLE 2, SECTION 316, SELLER SPECIFICALLY EXCLUDES ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE. SELLER DIRECTS PURCHASER TO FULLY INSPECT AND EXAMINE EACH ENCLOSED AUTOMOTIVE COMPONENT BEFORE INSTALLATION AND TO USE EACH AUTOMOTIVE COMPONENT AT PURCHASER’S OWN RISK. IN THE EVENT THAT ANY AUTOMOTIVE COMPONENT IS DEFECTIVE UPON PURCHASER’S RECEIPT, PURCHASER’S SOLE REMEDY SHALL BE TO RETURN THE DEFECTIVE AND UNUSED AUTOMOTIVE COMPONENT TO SELLER WITHIN FIFTEEN (15) DAYS AFTER PURCHASER’S RECEIPT AND REQUEST IN WRITING EITHER A FULL REFUND OR A REPLACEMENT, WHICH SELLER SHALL SHIP TO PURCHASER AT NO ADDITIONAL CHARGE.

Full Tilt Boogie Racing Inc........1817 Dolphin Drive.......Waukesha, WI  53186.........info@fulltiltboogieracing.com